Motion Detector Lights Troubleshooting

Indeed, in modern times, motion detector lights are considered to be the source of security or you can say, watchdogs if you speak about the safety of your own house. The best part about these lights is they automatically switch on when they sense any sort of motion, burglary, human or animal movement in the surrounding area of a residence. They stay on for a while and all the detector alarms go off automatically. Now, in this time of action, all the chaos that is aroused is good enough to instill fear in the burglar and scare him till the end. Since, these lights are so handy and useful to a homeowner and his property, it is obvious to keep a check on its regularity and proper functions, whether these lights work well or not. Because if they don't, apparently a motion detector lights troubleshooting procedure should be conducted. Look further into this article to learn about the simple ways of troubleshooting.

Troubleshooting Motion Detector Lights

Besides the lights, detecting even the slightest movement in a given area and actuating the light fixture to light up instantly, there can be certain problems and failures regarding motion sensor lighting. So, let's read about the same and learn how to troubleshoot motion sensor lights.

Clean the Lights
Well, because most of the lights are outdoor motion sensor lights, cleaning happens to be the most valid point though. Thus, clean all the motion detector light surfaces with a piece of cloth and a cleaning solution. There can be mildew, debris, dust, light attracted freaky insects stuck into the sensors and so on. These typical outdoor conditions soils the sensors, dims the capacity of the bulbs to emit proper light and ultimately give out on the fixture's normal functionality.

Check the Light Manually
By stating to check the light properly, means that a detector could be blocked due to some good reason eventually providing no power to the light. If you see a blockage, remove the interference that is causing it. Remember, interior lights have detectors on the switches and the ones that are on the exterior have detectors fixed directly on the light(s).

Dysfunctional Detector
Another possibility can be a bad, dysfunctional sensor. If you find out that the detector or the sensor is gone completely bad and the alarms aren't functioning well, it's time to change them. You can only learn about the state of a bad detector by using an electrical meter. This meter will help you know whether there is electricity running through the main power supply box or not. If the power is missing, perhaps the breaker is tripped and if the electric power is present, that means the detector has gone bad. Buy a new motion detector from the hardware store to fix the problem.

Fussy Light Bulbs
This is the most common problem under the subject of motion detector light troubleshooting, having erratic light bulbs which generally burn out in course of time. They are the main reason motion detector sensor lights do not work half the time. So, if you learn that the light bulbs aren't working, of course unscrew them and replace the old for new with the same wattage. After replacement switch on the bulb and check for its working condition.

Aim and Adjust the Motion Detector Sensor
If the detector lights do function but if they do not function at the right time, no point right!. For this reason, you will have to adjust the points of the sensor correctly. Choose the area where you want the light to respond to, then hold the detector at its back and tilt it slightly such that the light sensor directs in your chosen area. Next, set the distance of the motion detector light to monitor and slide the Sensory Adjustment Dial to medium, low or high state, depending on how far you want your motion detector light to respond to. Once, all this has been decided, slide the switch to next and test the detector for its working condition.

Set the Right Time
Time is valuable, indeed at a time like this! There is a choice of adjusting the time of your motion detector lights to remain on even after the object or movement has been detected in your surroundings. The time range is standard, i.e., 30 seconds to somewhere around 10 minutes long. If in this given time, the lights do not go off, then it's time to adjust the sensory adjustment dial located on the detector to feed in the right time for the light to stay on.

Although the fact is hard to deny, that with increasing technology in today's world, a human's life is becoming much easier day in and out. And one of the major contributors are these motion detector lights, which guards a homeowner and his property and gives him sound sleep at night. So, in case if you find any problem in the working of motion light sensors, follow these troubleshooting tips and fix the problem.