Can Crusher Design

Storing empty cans can take up a lot of space in the pantry, garage or basement or even the trash bin. A simple remedy would be to crush the cans for recycling, thus reducing waste. You can either buy a can crusher from the market or you can make one yourself. Making a can crusher is not difficult if you understand how its mechanism works. You also need to know a bit about woodworking. Make use of any of the following homemade can crusher design ideas, and you will find it is a fun exercise too. Let's first take a look at wooden can crusher design, using simple woodworking skills.

Can Crusher Design Ideas of Wood

Can crushers basically work on the principle of applying force to crush the can. The early can crusher was not a device but simply made direct use of one's foot. The basic wood can crusher design utilizes this same rationale in its construction.

Basic Wood Can Crusher Design - 1

Materials required
2" x 4" x 16" hardwood boards, 2
Strap hinge or door hinge kit (comes with screws)
Screen door handle kit (with screws)
Old jar lids, 2 (should be slightly larger size than a 16 oz can)
Screwdriver
1-inch screws or adhesive glue

Method
Using the strap hinge sets, attach the two boards together. With the help of the screws in the hinge set, fasten the hinge onto both the boards. Use a screwdriver to tighten the screws. The two boards should lie on top of each other when you close the hinge. Attach the jar lids onto the front of the boards, with the help of the 1-inch screws (you can even stick them onto the board with the help of adhesive glue). Make sure they are attached on the opposite side to the hinge. Your can crusher is almost ready. Check whether the jar lids are on top of each other, when closed. Now, attach the door handle exactly across the hinge side and the lids. To attach the door handle, use the hardware that comes with it. Tighten the screws with the help of a screwdriver.

Now, your can crusher is ready to be tested. Keep the can crusher on a hard surface. Place the can on the bottom board. Using the door handle bring the board down on top of the can. The two jar lids keep the can in place, while you hold the top board by the door handle and bring it down with force to crush the can.

Basic Wood Can Crusher Design - 2

Materials required
15½" x 2" x 4¾" wood pieces, 2
Strap hinge or door hinge kit
Screen door handle kit
Screwdriver

Method
Attach the wood pieces on either sides of the hinge, in such a way that the top and the base boards fall flat on each other when the hinge is in closed position. First, fasten one side of the hinge to the center of the shorter end (4¾" side) of one of the wood pieces, with the help of screws in the hinge kit. See that the wood is not on the inside of the hinge and that the latter is not on the 4¾" x 2" side of the wood piece.

Then, affix the loose end of the hinge to the other piece of wood in the similar way, so that the hinge is attached on one side (2" x 15½") of the wood. Remember, you need to ensure that at the end the hinge should be able to close, with the two pieces of wood one over the other. Close and open the hinge to check if it's been fixed correctly. Next, on top of one wood piece (opposite side of the hinge), fix the screen door handle with the help of screws provided in the kit. Once this is done, you can use the can crusher.

Keep the can crusher on a stable surface. Leverage the top of can crusher to an approximate angle of 45 degrees and place a can between the wood pieces, close to the hinge. Push the top of the can crusher with force, to crush the can.

Complex Wooden Can Crusher Design

Using this can crusher design will need more than basic woodworking tools and skills. If you're new to woodworking, it would be advisable to seek the help of someone who is experienced at it.

Materials required
¾" x 6" x 39" Hardwood board
#8 2" Wood screws, 7
Wood washers, 2
3/8" Dia Washers, 4
3/8" Cap nuts, 6
3/8" x 1¾" Carriage bolts, 2
3/8" x 8" Hex head guide bolts, 2
3/8" x 7" Threaded rods, 3
1/16" x 3¼" x 2-7/8" Plastic laminate, 2
Adhesive glue
Polyurethane varnish
Drill and bits

Method
Before beginning to assemble the can crusher, you need to get the wood parts together. So, take the wood board and cut it into base, arms, handle, sides handles, and jaw pieces (jaws should be slightly larger to enable trimming later) as indicated below.

From the hardwood board, cut the following:
3/4" x 5" x 12" Base
3/4" x 1-3/8" x 20" Arms, 2
11/8" x 5 Handle
3/4" x 3" x 6" Sides, 2
3/4" x 3¼" x 2-7/8" Jaws, 4

Once the wood pieces are ready, you can make two pairs of the jaw pieces with the help of adhesive glue. Keep the jaws aside for the glue to dry. Now, drill holes for the bolts in the side and arm parts of the can crusher. Make sure the bolt holes conceal the bolt heads. Next, using a 3/8" round-over bit, trim the front edges of the side pieces to a ¾" radius. Do the same with all edges of the arms too. Next, you need to get a 1-1/8" dia dowel for the handle and two washers. The dowel should be 3" long for the latter. Then using a 3/8" brad point bit in your drill, bore through holes in the center of both the ends of the dowel. Use a hand-screw clamp to bore the holes straight. Next, cut the 3" long dowel to match length of the washers.

Now, check if the two jaw parts are dried before you cut them to the finish size. With the help of a contact adhesive, cover the face of the jaw with the plastic laminate. Once dried, trim it flush and soften the edges, using a mill file. Now, you need to drill holes for the guide bolts that go through the upper jaw and ¾" deep in the lower jaw (use smaller bit for the lower jaw). The bolt holes for the latter should be smaller, so they hold the threaded end of the guide bolt firmly. Don't forget to drill pivot holes into the jaw sides. After the drilling is done, using a ¾" round-over bit, rout the bottom edge of the back of the lower jaw. This will ensure that the pivot can move easily against the base.

Now, we can move to the hardwood base, to fit together the wood pieces to make the can crusher. Drill countersunk pilot holes to fit #8 2" wood screws after placing the side parts on the base. Separate the pieces and spread glue in the butt joints, before screwing them together. Now, smoothen the front edges of the base with the round-over bit. Drill three more pilot holes in the base for wall mounting.

At this point, cover the exposed wood parts of the can crusher with polyurethane coating a couple of times. This will ensure its long life and easy cleaning, once in use. Now, we need to attach the other parts to make the can crusher usable. Take the three 7" long threaded rods to assemble the handle and jaw pieces, with the help of cap nuts. Once done, keep the jaws and handle open fully. Now, pour a quick-setting epoxy into the holes of the lower jaw. Drive in the guide bolts till their heads are a 1/16" top of upper jaw. Now, the all-wood can crusher is ready to mount on the wall and use.

Hope that the can crusher design ideas described above will prompt you to make one for yourself. These simple and not-so-simple, homemade can crushers made of wood are not expensive. When you choose the wood pieces, make sure they are able to withstand the force that you apply when crushing the can. Homemade can crushers are easy to use and sturdier (last longer) than the ones available in the store. Once you start to crush cans, don't forget to keep a bin handy or under the can crusher, so the crushed cans can neatly fall into it.